Source This Article

Just about every person has got their own individual rationale about Installing A Bathtub.

Setting up a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a new one is additionally a moderately difficult project. If the old bathtub is readily available, the project can relocate quickly; if you need to open up a wall surface to remove the old tub and also position the brand-new bath tub, the job is much harder. In either case, the project is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to take into consideration employing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This short article will help you install a brand-new bath tub in your shower room if you have currently gotten a brand-new bathtub and don't need to change the plan of your previous supply of water pipelines.
Your tools and also product checklist must consist of the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Preparing for the Setup

To start with, the sustaining framework provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.

Removing Old Touches

If you require to replace old faucets with new ones as a part of your setup, then the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be quite troublesome as a result of the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

Installing the Tub

Using the two wooden boards under its feet, put the bath tub in the needed setting. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub until the spirit level reads level.
To mount faucets, fit the bottom of the outermost versatile tap port to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Activate the water and check all joints and new pipework for leakages and tighten them if essential. Load the bathtub and likewise check the overflow outlet and also the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its final setting.

Fitting New Taps

If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the various other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Secure the faucet in position with the manufacturer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The former kind needs to be linked to the tap ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.

Tiling Around the Bath tub

In the area where the bath fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, leading to complications with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily offered on the market. It is advisable to fit the floor tiles utilizing waterproof or water-proof glue and cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Hopefully you liked our piece about Tools You Need to Install a New Bathtub . Many thanks for taking the time to read through our posting. Loved our blog? Please share it. Help someone else find it. We treasure reading our article about How to Install a Bathtub.

Estimate Free